24/7 Plumbing Emergency Hotline Call 1300 721 996
Sales - AUSTRALIA WIDE Service & Installs - Sydney - Central Coast - Adelaide - Brisbane - Newcastle - Wollongong - Melbourne - Perth - ACT

What to Check on Your Hot Water System Before You Buy a House

real estate agent handing over key to sold house

Before you buy a house, check the hot water system’s age on its data plate, its type and fuel source, whether its capacity suits your household, any leaks or rust, and the compliance paperwork. A building inspection may only check the tap, and you don’t need to be a plumber to do any of this. Most of it is visual and takes a few minutes.

Why the Hot Water System Needs Its Own Check Before You Buy

A pre-purchase building inspection is a visual inspection, and plumbing services are generally outside its scope. Some reports record only that hot water came out of the tap, so ask your inspector exactly what they cover.

When the agent says the hot water system is fine, that usually means it works today. It doesn’t tell you how old it is, who installed it or how much life it has left. If it’s near the end, the replacement cost lands on you after settlement. Under current plumbing rules, a replacement generally needs temperature control at the bathroom outlets, which older systems may not have, so the bill can be more than a straight swap.

How to Tell How Old the Hot Water System Is

Find the data plate, the label on the side or front of the unit. It lists the model, the capacity and usually the manufacture date. On some units, the date is part of the serial number, which the manufacturer can usually decode. Take a photo of it.

Lifespan depends on the type, water quality and servicing, so treat these as rough guides only.

System Commonly quoted lifespan
Electric storage 8 to 15 years
Gas storage 8 to 15 years
Gas continuous flow 10 to 20 years
Heat pump 10 to 15 years
Solar 10 to 20 years, and the collectors, tank, pump and booster can each age differently

If the hot water system is at or past the lower end of its range, treat replacement as a likely near-term cost and budget for it before you make an offer. If the plate is missing or unreadable, ask the vendor.

Identify the System Type and Fuel Source

Each type has its own running costs and replacement path, so know which hot water system you’re looking at.

Type How to spot it What to look for
Electric storage A tank with an electrical supply and no flue, indoors, outdoors or in the roof Rust or water at the base, and which circuit it runs on
Gas storage A tank with a flue on top and a gas connection Soot or scorch marks around the flue or burner
Gas continuous flow A compact wall-mounted unit with no tank, inside or outside Discoloured casing, a damaged flue, signs of overheating
Heat pump An all-in-one unit with the compressor on top of the tank, or a tank with a separate outdoor compressor Damage to the unit, blocked airflow, service records
Solar Roof panels with a tank on the roof or the ground Cracked glass or damaged panels, and whether the booster is electric or gas

Running costs depend a lot on the electricity tariff. Many electric storage systems are wired to a separate off-peak or controlled load circuit with a cheaper rate. Whether that is still available depends on your retailer and network, so ask the vendor how the system is wired and confirm with your retailer.

Changing fuel type later can mean new gas or electrical work on top of the system itself, so make sure you are happy with it and that it suits you before buying.

Check Whether the System Suits Your Household

Keep in mind that the hot water system was sized for the current owners, so what works for them might not work for you. Check the capacity on the data plate, which is in litres for a storage tank and litres per minute for a continuous flow unit. Then picture your own busy mornings, with everyone who lives there, every bathroom in use, and two showers running while the dishwasher is on.

Say the vendors are a couple in a one-bathroom home and you’re a family of five with two bathrooms. A tank that suited them will probably run out on the first school morning, and a continuous flow unit has the same problem if it can’t supply two showers at once. Going too big isn’t the answer either, because a larger system costs more to heat.

If it doesn’t suit you, you can negotiate on price or ask for a replacement, budget for an upgrade yourself, or walk away. A size mismatch alone usually isn’t a dealbreaker, but it belongs in your numbers.

Visual Condition Checks at the Open Home

You can check all of this without touching anything.

  • Rust or water at the base of the tank, or damp ground or flooring around it.
  • The relief valve drain line, the pipe running down from the valve near the top of a storage tank. A small amount of water escaping while the system heats is normal. Water running steadily is not. A separate expansion valve on the cold water line can also drip while heating.
  • A brown or orange tinge in the hot water. Run a bathroom hot tap for a minute. It can point to rust or sediment in the tank or old pipework.
  • Soot or scorching around a gas unit’s flue or burner, which can point to a combustion or installation problem. If you smell gas, leave and tell the agent.
  • Cracked glass, bent fins or a dented casing on solar collectors and heat pump units, and banging, popping or hissing when the system heats.

Don’t touch valves, remove covers or block the drain line. If something looks off, take a photo, make a note and ask the vendor about it in writing through your agent.

A tidy-looking hot water system can still be 13 years old, never serviced or installed without a compliance certificate, and none of that shows from the outside.

Safety and Compliance Items to Confirm

A hot water system deals with scalding water, gas and mains power, so a poor installation is a safety risk. A compliance certificate generally shows the work was done by a licensed trade, and a missing one can complicate insurance, warranty claims, and a future sale.

  • A licensed plumber handles the water side, including the relief and tempering valves. Gas appliances need someone licensed for gas fitting, which in some states is a separate licence. Hard-wired electrical connections need a licensed electrician.
  • A compliance certificate exists for the installation (you can ask to see it).
  • Storage systems have a temperature and pressure relief valve with a drain line.
  • Water at showers, baths and basins is limited to 50°C, using either a tempering valve or a heater designed not to exceed that temperature. Tanks hold water at 60°C or above. Systems installed before the rules applied may not have a tempering valve.

If the vendor can’t produce the paperwork, ask for it in writing. If it doesn’t exist, have a licensed plumber assess the installation and budget for anything they say is needed.

Compliance requirements and licensing standards vary by Australian state and territory. Confirm current requirements with your state’s plumbing regulator or local council before relying on this information.

Questions to Ask the Selling Agent or Vendor

Ask this Why it’s important
When was the system installed, and by whom? Confirms age and whether licensed trades did the work
Can I see the invoice, compliance paperwork and any warranty documents? Shows the installation was documented, and warranty terms vary
Has it been serviced, and are there records? Regular servicing suggests it has been looked after
What tariff or circuit does it run on? Affects running costs, especially for electric and heat pump systems
Are there any known faults or past repairs? Gives the vendor a chance to tell you
For heat pump or solar, was a rebate claimed, and were there conditions? Schemes and eligibility vary by state and change often

Bring your conveyancer in early, as they can check the contract for special conditions and advise how to raise your findings with the vendor. Cooling-off periods and inspection windows vary by state, and auction sales usually don’t have a cooling-off period, so find out how long you have to get a plumber through.

What to Do If the Hot Water System Fails Your Checks

A failed check is a cost to manage, not automatically a reason to walk away.

  1. Keep your photos, the data plate image and the vendor’s answers.
  2. Get a licensed plumber to assess the hot water system, plus a gas fitter or electrician if the problem sits in their area. Do this before contracts are binding if you can.
  3. Talk to your conveyancer about your options: asking the vendor to repair or replace the system, negotiating on price, or budgeting for a replacement yourself.

As noted above, this checklist is general information and doesn’t replace a licensed plumber’s inspection.

What to Do If Your Hot Water System Doesn’t Pass the Checks

If you do need a replacement, Same Day Hot Water Service can supply and install a new system, with same-day installation possible in many cases. We’re a family business with over 30 years in hot water, servicing Sydney, Melbourne, Brisbane and our other areas. Call us on 1300 721 996, and we’ll talk you through your options.

FAQs

What should I look for on a solar or heat pump hot water system

Check the collectors or outdoor unit for damage, ask what the booster runs on, and ask for service records. These systems have more parts than a basic tank, so have a specialist look at them before you commit.

What if the hot water system has no tempering valve or compliance certificate?

Older systems may predate current requirements, which generally apply when a system is installed or replaced, though states differ. Ask a licensed plumber what applies to this house, and ask the vendor for any paperwork they hold.

Will the warranty or a rebate transfer to me?

Warranty terms vary by manufacturer and may depend on the original installation records, so get the documents and check with the manufacturer. Rebate schemes vary by state and change often, so check current rules before counting on one for a future replacement.

What will it cost if I have to replace it?

It depends on the system type and size and what the installation involves, including any gas, electrical or tempering valve work. A licensed plumber or supplier, including Same Day Hot Water Service, can quote for the property.

same day hot water service logo

Enter your username and password to log into your account